User Menu

You have access to many functions in the User Menu that can be accessed from the keypad. Enter your user code and the functions you have access to, display. The User Menu allows you to create user profiles, add, change, and delete user codes, create favorites with your Z-Wave devices, and more.
Below are the User Menu functions and their processes as you will see them on the keypad. Before using a function, you will need to access the User Menu.

Access the User Menu

1. Press CMD until MENU? NO YES displays.

2. Select YES.

3. Enter your user code and press CMD.

User Check-In

1. Access the User Menu.

2. Press CMD until USER CHECKIN displays.

3. Press any select key or area. The keypad displays USER CHECKIN: 22 (22 = user number).

4. The panel sends the Check-in Report containing your account number and user number to the email address or cell phone number.

Zone Activity Check

1. Access the User Menu.

2. Press CMD until ACTIVITY CHECK? displays.

3. Press any select key or area. The keypad displays ENABLE? YES NO. The default is YES.

   • When NO is selected, the keypad displays CHECK DISABLED for four seconds and then sends the Activity Check Disabled message to the central station.

   • When YES is selected, the keypad displays CHECK ENABLED for four seconds and then sends the Activity Check Enabled message to the central station.

Sensor Reset

Sensor Reset resets panic and fire sensors after they have been tripped. They must be reset before they can detect any additional alarm conditions. A sensor reset is also required after replacing batteries in wireless devices.

Reset All Sensors

1. Access the User Menu.

2. Press CMD until SENSOR RESET? displays.

3. Press a select key or area. The keypad displays SENSORS OFF followed by SENSORS ON.

Reset Your Fire Sensor

Press 2 for two seconds then enter your user code.

Outputs On/Off

Use this function to individually turn your system’s outputs on and off. Your system may use outputs to control door access, interior and exterior lighting, heating, air conditioning, and other appliances.

Turn Outputs On and Off

1. Access the User Menu.

2. Press CMD until OUTPUTS ON/OFF displays.

3. Press any select key or area.

4. Enter the output number, then select ON or OFF.

Z-Wave Setup

Z-Wave technology adds home automation to your system. Using Z-Wave, you can control lights, locks, small appliances, and thermostats from your keypad, Virtual Keypad App, or VirtualKeypad.com. You can add up to 140 Z-Wave devices to your system.

Begin Here

1. Access the User Menu.

2. Press CMD until ZWAVE SETUP? displays.

3. Press any select key or area. The keypad displays ADD LIST REMOVE. Press CMD to display FAV XFER OPT.

Note: To access favorites on 7-Inch Touchscreen Keypads, press Favorite or the Z-Wave device in the Carousel menu. Press the Settings icon in the bottom right corner.

Add a Z-Wave Device

1. Select ADD.

2. Press the button on the Z-Wave device when PRESS BUTTON ON DEVICE TO ADD displays on the keypad.

3. Press CMD when DEVICE FOUND displays.

4. Press any top row select key or area and name the device.

5. Press CMD to save the device.

List Z-Wave Devices

1. Select LIST and DEVICE LIST displays.

2. Press CMD to advance through the list of Z-Wave devices.

3. Press any select key or area to display DEVICE RENAME STATUS.

4. Select RENAME and name the device then press CMD.

Remove a Z-Wave Device

1. Select REMOVE.

2. Press the button on the Z-Wave device when PRESS BUTTON ON DEVICE TO REMOVE displays on the keypad.

Status of a Z-Wave Device

1. Select LIST and DEVICE LIST displays.

2. Press CMD to advance through the list of Z-Wave devices.

3. Press any select key or area to display DEVICE RENAME STATUS.

4. Select STATUS. The device name and OKAY display when the device communicates. The device name and FAILED display if the device stored in the system does not communicate.

5. Press CMD and REMOVE FAILED DEVICE displays.

6. Select YES to remove the failed device from your system. Select NO to leave the device in your system.

Transfer Controller Operation

Use this function to transfer and replace your existing Z-Wave device information with information from another system.

1. Select XFER. The keypad warns you that transferring Z-Wave device information deletes all your Z-Wave devices connected to your system.

2. Select YES to proceed.

3. Initiate the transfer at the other manufacturer’s Z-Wave portable controller. ZWAVE SETUP? displays.

Optimize Z-Wave Devices

Select OPT. The keypad displays OPTIMIZE SUCCESS when communication with a Z-Wave device is established.

Favorites

Favorites are preset combinations that allow you to quickly activate multiple Z-Wave devices at once. You can create a Favorite that turns down your thermostat, turns off your lights, and locks your front door when you leave the building. You can add up to 25 devices to a Favorite.

Begin Here

1. Access the User Menu.

2. Press CMD until ZWAVE SETUP? displays.

3. Press any select key or area. The keypad displays ADD LIST REMOVE. Press CMD to display FAV XFER OPT.

4. Select FAV. At FAVORITE NUMBER:, enter a number between 1 and 20 and press CMD. ADD EDIT REMOVE display.

Note: To access favorites on 7-Inch Touchscreen Keypads, press Favorite or the Z-Wave device in the Carousel menu. Press the Settings icon in the bottom right corner.

Add Devices to a Favorite

1. Select ADD.

2. Press CMD to browse your Z-Wave devices.

3. Press any select key or area to assign a device to a Favorite.

Edit Devices in a Favorite

1. Select EDIT.

2. Press CMD to browse your Z-Wave devices.

3. Press any select key or area to view a device’s settings. Refer to the Lights, Doors, and Thermostat sections on this page to edit your devices.

Lights

Press the select key or area for the desired setting when SETTING: ON OFF DIM displays.

• Select ON or OFF to turn a device on or off.

• Select DIM, enter the dim level (1-10) of the device, and press CMD.

Doors

• Doors: Press the select key or area for the desired setting when SETTING: LOCK UNLOCK displays

• Garage Doors: Press the select key or area for the desired setting when SETTING: OPEN CLOSE displays.

Thermostats

Press the select key or area for the desired setting when SETTING: OFF CL HT displays.

Off

1. Select OFF to display FAN SETTING:.

2. Press any select key or area. When ON AUTO displays, press the select key for the desired option.

Cool

1. Select CL and press any select key or area.

2. Enter the new temperature and press CMD.

Heat

1. Select HT then press any select key or area.

2. Enter the new temperature and press CMD.

Appliances (7-Inch Only)

Use the multilevel slider on the right side of the device to set the device at 0, 25, 50, 75, or 100. 0 is Off and 100 is On.

Remove Devices in a Favorite

1. Select REMOVE then press CMD to view your devices.

2. When the desired device displays, press any select key or area to remove that device.

3. Select YES when REMOVE DEVICE FROM FAV? NO YES displays.

System Wi-Fi Setup

Use this function if your system is connected through Wi-Fi.

Begin Here

1. Access the User Menu.

2. Press CMD until WIFI SETUP? displays.

3. Press any select key or area and the keypad displays WPS LIST MANUAL. Press CMD to display TEST.

Use WPS to Connect Your System

1. Press the WPS button on your Wi-Fi router.

2. Select WPS on your keypad and SEARCHING displays.

3. When WPS is successful, CONNECTED displays on your keypad. If WPS was not successful, WPS FAILED RETRY? NO YES displays.

4. Press YES to retry. Press NO and WPS LIST MANUAL displays.

List the Available Networks

1. Select LIST and SEARCHING displays.

2. Press CMD to view the available Wi-Fi networks.

3. When the desired network displays, press any select key or area to connect.
   W/L KEY:**************** displays.

4. If the system is unable to detect the security type, press any select key or area on the keypad and
   WEP WPA NONE displays. Select the desired security type and enter your network password. See Type On Your Keypad.

Manually Connect Your System

1. Select MANUAL.

2. Enter the name of your Wi-Fi network and press CMD. W/L KEY:**************** displays.

3. If the system is unable to detect the security type, press any select key or area on the keypad and
   WEP WPA NONE display. Select the desired security type then enter your network password. See Type On Your Keypad.

Test the Network Connection

Select TEST. When the test is successful, CONNECTED displays. If the test is unsuccessful, NOT CONNECTED displays.

Keypad Wi-Fi Setup (7-Inch Only)

Use this option to access additional features on your 7-Inch Touchscreen Keypad.

1. Select Options from the Carousel menu.

2. Select Wi-Fi Settings.

3. Select the Wi-Fi network you would like to connect to.

4. Enter the Wi-Fi password and select CMD.

Note: The 7-Inch Touchscreen Keypad needs to be connected to Wi-Fi to enable video features, events, and remote update capabilities.

Zone Status

Zone status allows you to check the status of each zone, displaying a list of armed, bypassed, and alarmed zones.

Check Zone Status

1. Access the User Menu.

2. Press CMD until ZONE STATUS? displays.

3. Press any select key or area to display ARM BYPS ALR NBR.

   • Select ARM for a list of currently armed zones.

   • Select BYPS for a list of currently bypassed zones.

   • Select ALR for a list of currently alarmed zones.

   • Select NBR to find a specific zone number.

4. Select the desired option and the zones related to that option display with a zone status of OKAY, BYPS, or BAD.

Bypass Zones

Follow these steps to bypass a zone from the User Menu. Fire, panic, emergency, supervisory, and 24-hour zones cannot be bypassed.

1. Access the User Menu.

2. Press CMD until BYPASS ZONES? displays.

3. Press any select key or area. The keypad displays ZONE: - RST BYPS.

4. To bypass a zone, enter the zone number and select BYPS. The zone number automatically disappears and a new zone number can be entered. Refer back to step 3. Confirmation will be given when the zone has been bypassed.

5. To reset a zone, enter the zone number and select RST. Confirmation will be given when the zone is reset.

Note: Bypass can be accessed through the Carousel menu on Touchscreen Series Keypads.

Zone Monitor (Chime)

1. Access the User Menu.

2. Press CMD until ZONE MONITOR? displays.

3. Press any select key or area. The keypad displays PERIM ALL NBR. When a zone trips, it will display ALERT on the keypad.

4. Select PERIM to place all perimeter zones into Zone Monitor.

   • The keypad displays PERIM? ADD RMV.

   • Select ADD to add all perimeter zones to Zone Monitor.

   • Select RMV to remove all perimeter zones.

5. Select ALL to place all zones into Zone Monitor.

   • The keypad displays ALL? ADD RMV.

   • Select ADD to add all Night and Exit zones to Zone Monitor.

   • Select RMV to remove all Night and Exit zones.

6. Select NBR to enter a specific zone number for zone monitor.

7. If NBR is selected, the keypad displays ZONE : - ADD RMV.

   • Enter any zone number and select ADD to add this zone.

   • Enter any zone number and select RMV to remove the zone.

8. The zone number automatically disappears and a new zone number can then be entered. See step 7.

System Test

1. Access the User Menu.

2. Press CMD until SYSTEM TEST? displays.

3. Press any select key or area. The system test begins automatically and the keypad displays:

   • BELL SOUNDING during a two second bell test

   • KEYPAD SOUNDING during a two second keypad test

   • BATTERY - OKAY or BATTERY - TRBL to indicate the battery condition

   • TRANSMIT TEST * and ATTEMPT NO : 1 during the transmit test

   • TRANSMIT OKAY or TRANSMIT FAILED to show the transmit test results

   • TEST END to indicate the System Test is complete.

4. Press the Back Arrow key to end the system test.

Note: The transmit test does not occur on local systems.

Testing Your System Burglary Protection

The System Test function should be part of your weekly testing and should be followed by placing the interior and perimeter burglary devices in Zone Monitor mode. This allows you to open and then close each protected door and window while listening for the keypad to beep confirming its operation.